Passed Exam Today H12-831_V1.0

Comprehensive and Detailed In-Depth Explanation:

The Link Layer Discovery Protocol (LLDP) is used for discovering neighboring devices. The given LLDP output contains key details about the neighboring device (R2), including its system name, interface, and management IP address. Let's analyze each option carefully:

Option A: "The sysname of the peer device is R2." ✅ Correct

The output clearly shows System name: R2, which confirms that the neighbor's system name is indeed R2.

Option B: "The interface number of the peer device is GE0/0/0." ✅ Correct

The Port ID in the LLDP output is GE0/0/0, which matches the statement in Option B.

Option C: "The VLAN ID of the peer device is 1." ❌ Incorrect

The given LLDP output does not mention any VLAN ID information. Therefore, this option is false.

Option D: "The management IP address of the peer device is 192.168.1.1." ✅ Correct

The Management address field in the LLDP output confirms the IP address as 192.168.1.1, making this statement true.

HCIP-Datacom-Advanced Routing & Switching Technology References:

Huawei HCIP-Datacom Official Certification Guide, Chapter on LLDP and Network Device Discovery.

HCIA/HCIP Datacom Training Materials – LLDP Neighbor Discovery Commands.

Huawei Datacom Configuration Guide – Section on display lldp neighbor interface.

Step 1: Understanding OSPF Areas and Summarization

Area 1 (NSSA - Not So Stubby Area)

Allows external routes but converts Type-5 LSAs into Type-7 LSAs.

External routes must be translated by an ABR into Type-5 LSAs before being propagated into other areas.

Area 2 (Common Area - Regular OSPF Area)

Supports both inter-area and external routes.

asbr-summary 10.0.4.0 255.255.255.0 Command

This command summarizes all external routes within 10.0.4.0/24 into a single summarized route.

Since it is applied on R1 and R3, these routers will advertise 10.0.4.0/24 instead of 10.0.4.4/32 to their respective areas.

Step 2: Route Distribution Analysis

R4 (Originating Router in NSSA - Area 1)

R4 injects 10.0.4.4/32 as a Type-7 LSA into Area 1.

R1 (ABR between Area 1 & Area 0, Summarizing Route)

Since R1 is an ABR, it translates Type-7 LSAs from Area 1 into a summarized Type-5 LSA (10.0.4.0/24) for Area 0.

✅ R1 has 10.0.4.0/24 in its routing table.

R2 (Inside Backbone Area 0, No ASBR Summary Applied Here)

R2 only receives Type-5 LSAs from R1 but does not summarize them.

Since R2 is not explicitly summarizing, it will likely still see 10.0.4.4/32 rather than 10.0.4.0/24.

❌ R2 does not have 10.0.4.0/24.

R3 (ABR between Area 0 & Area 2, Summarizing Route)

R3 is also an ABR and has the asbr-summary 10.0.4.0/24 command configured.

It will advertise the summarized route 10.0.4.0/24 into Area 2.

✅ R3 has 10.0.4.0/24 in its routing table.

R5 (Inside Area 2, No Direct Connectivity to External Routes)

Since R3 summarizes 10.0.4.0/24, R5 (inside Area 2) will receive only summarized routes.

✅ R5 has 10.0.4.0/24.

Final Answer: ✅ R1, R3 (Option A, C)

References:

HCIP-Datacom-Advanced Routing & Switching Technology V1.0 – OSPF Route Summarization

OSPF NSSA and Type-7 to Type-5 LSA Translation

Comprehensive and Detailed In-Depth Explanation:

1. Understanding the Network Topology

R1 and R2 are OSPF-enabled routers connected via the 10.0.12.0/24 subnet (Area 0).

PC1 (192.168.1.2/30) is connected to R1 via GE0/0/1.

PC2 (192.168.1.22/30) is connected to R2 via GE0/0/1.

OSPF ensures that R1 and R2 know about each other's directly connected networks.

2. Analyzing Connectivity

Can R1 ping 192.168.1.22 (PC2)?

Yes, if routing is properly configured.

OSPF ensures that R1 learns about 192.168.1.22 from R2.

Since R1 has a route to 192.168.1.22 via R2, it can ping PC2 successfully.

✅ Option A is correct.

Can R1 ping 192.168.1.21 (R2's interface)?

Yes, since R1 and R2 are OSPF neighbors.

R1 learns 192.168.1.21 via OSPF and can reach it directly.

✅ Option B is correct.

Can R2 ping 192.168.1.2 (PC1)?

Yes, since OSPF ensures that R2 learns about 192.168.1.2 from R1.

Since R2 has a route to 192.168.1.2 via R1, it can ping PC1 successfully.

✅ Option C is correct.

Can PC1 and PC2 ping each other?

Yes, if default gateways and routing are configured correctly.

If R1 and R2 can ping each other and forward packets, PC1 and PC2 should be able to communicate.

❌ Option D is incorrect because PC1 and PC2 should be able to ping each other.

Final Answer:

✅ A, B, and C are correct.

HCIP-Datacom-Advanced Routing & Switching Technology References:

OSPF Inter-Router Communication and Route Advertisement

Default Gateway and Routing in Multi-Router Networks

Troubleshooting End-to-End Connectivity in Routed Networks