Sure Pass Exam XK0-005 PDF

The issue is that the administrator did not set the default target to graphical.target. A target is a unit of systemd that groups together other units by a common purpose or state. The graphical.target is a target that starts the graphical user interface (GUI) along with other services. The administrator used the command systemct1 isolate graphical.target to switch to this target temporarily, but this does not change the default target that is activated at boot time. To make this change permanent, the administrator should have used the command systemct1 set-default graphical.target, which creates a symbolic link from /etc/systemd/system/default.target to /usr/lib/systemd/system/graphical.target.

The other options are not correct explanations for the issue. The administrator did reboot the server properly by using systemct1 reboot, which shuts down and restarts the system cleanly. The administrator did not need to set the default target to basic.target, which is a minimal target that only starts essential services. The administrator did not shut down the server improperly, which could have caused file system corruption or data loss, but not affect the default target. References: systemct1(1) - Linux manual page; How to Change Runlevels (targets) in SystemD

The administrator can use the following two options to boot the system into the single user mode:

Interrupt the boot process in the GRUB menu and add systemd.unit=rescue.target in the kernel line. This option will boot the system into the rescue mode, which is a minimal environment that allows the administrator to perform basic tasks such as repairing the system. The GRUB menu is a screen that appears when the system is powered on and allows the administrator to choose which kernel or operating system to boot. The kernel line is a line that specifies the parameters for the kernel, such as the root device, the init system, and the boot options. The administrator can interrupt the boot process by pressing the e key in the GRUB menu and edit the kernel line by adding systemd.unit=rescue.target at the end. This option will tell the system to use the rescue target, which is a unit that defines the state of the system in the rescue mode. The administrator can then press Ctrl+X to boot the system with the modified kernel line. This option will boot the system into the single user mode and allow the administrator to troubleshoot the issues.

Interrupt the boot process in the GRUB menu and add systemd.unit=single.target in the kernel line. This option will boot the system into the single user mode, which is a mode that allows the administrator to log in as the root user and perform maintenance tasks. The GRUB menu and the kernel line are the same as the previous option. The administrator can interrupt the boot process by pressing the e key in the GRUB menu and edit the kernel line by adding systemd.unit=single.target at the end. This option will tell the system to use the single target, which is a unit that defines the state of the system in the single user mode. The administrator can then press Ctrl+X to boot the system with the modified kernel line. This option will boot the system into the single user mode and allow the administrator to troubleshoot the issues.

The other options are incorrect because they either do not boot the system into the single user mode (execute the following command from the GRUB rescue shell: mount -o remount, ro/sysroot or interrupt the boot process in the GRUB menu and add systemd.unit=single in the kernel line) or do not use the correct syntax (interrupt the boot process in the GRUB menu and add single=user in the kernel line or interrupt the boot process in the GRUB menu and add init=/bin/bash in the kernel line). References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 8: Managing the Linux Boot Process, pages 267-268.

The server’s firewall is preventing connections from being made, which is causing the connectivity issue. The output of iptables -L -n shows that the firewall is blocking all incoming traffic on port 22, which is the default port for SSH. The output of ssh -v user@104.21.75.76 shows that the connection is refused by the server. To resolve the issue, the administrator needs to allow port 22 on the firewall. The other options are incorrect because they are not supported by the outputs. The workstation has the correct IP settings, as shown by the output of ip addr show. The sshd service is enabled and running, as shown by the output of systemct1 status sshd. The server has the correct default gateway configuration, as shown by the output of ip route show. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 13: Managing Network Services, pages 406-407.

The command that would resolve the issue is chmod 600 .ssh/authorized_keys. This command will change the permissions of the .ssh/authorized_keys file to 600, which means that only the owner of the file can read and write it. This is necessary for SSH key authentication to work properly, as SSH will refuse to use a key file that is accessible by other users or groups for security reasons. The output of ls -l shows that currently the .ssh/authorized_keys file has permissions of 664, which means that both the owner and group can read and write it, and others can read it.

The other options are not correct commands for resolving the issue. The restorecon .ssh/authorized_keys command will restore the default SELinux security context for the .ssh/authorized_keys file, but this will not change its permissions or ownership. The ssh_keygen -t rsa -o .ssh/authorized_keys command is invalid because ssh_keygen is not a valid command (the correct command is ssh-keygen), and the -o option is used to specify a new output format for the key file, not the output file name. The chown root:root .ssh/authorized_keys command will change the owner and group of the .ssh/authorized_keys file to root, but this will not change its permissions or make it accessible by the user who wants to log in with SSH key authentication. References: How to Use Public Key Authentication with SSH; chmod(1) - Linux manual page