Free and Premium Huawei H35-480_V3.0 Dumps Questions Answers

According to Huawei's official documentation, gNodeBs send TPC (Transmit Power Control) commands to UEs over PDCCHs to control the transmit power of PUCCH (Physical Uplink Control Channel) and PUSCH (Physical Uplink Shared Channel).

Cloudification of 5G wireless networks can significantly improve the user rate. Cloudification refers to the process of virtualizing the functions of a network and running them on commodity hardware in a data center, rather than on dedicated hardware in the network itself. In the case of 5G wireless networks, this can be achieved by virtualizing the Base Station (gNB) functions and running them on a cloud platform. This allows for more efficient use of resources and better scalability, which can result in an improved user rate.

Additionally, Cloud-RAN (C-RAN) architecture, which is a cloud-based centralization of the baseband processing functions can also be used to improve the user rate by reducing the number of active base stations required in a given area, and also by allowing for more efficient management of resources and more flexible deployment of services.

However, it's worth noting that the improvement of the user rate is not only limited to cloudification, but it's also related to many other factors such as network design, optimization, and management.

According to the 3GPP TS 24.008 V15.2.0 ( after the cell search is complete, a 5G UE automatically selects a PLMN based on the priority sequence. The UE will preferentially select U-PLMN (User Preferred PLMN) for registration. U-PLMN is the PLMN that the user has selected manually or that the user has previously registered with, and it has the highest priority. If U-PLMN is not available, the UE will select RPLMN (Registered PLMN), which is the last registered PLMN. If RPLMN is not available, the UE will select HPLMN (Home PLMN), which is the PLMN that is permanently stored in the UE. Finally, if HPLMN is not available, the UE will select EHPLMN (Equivalent HPLMN), which is the PLMN with the same MCC and MNC as HPLMN.

According to the Huawei SA Networking Product Design Guide ( the downlink data split modes supported on the gNodeB side in the 5G NSA Option 3x architecture are A. MCGONLY: only split to the MCG and D. SCGANDMCG: dynamic data split. The MCGONLY mode is used when all the UE data must be sent to the same MCG, while the SCGANDMCG: dynamic data split mode is used when the data is split between multiple SCGs and MCGs.

The correct answers are A. DMRS of the uplink PUSCH of the UE and B. Downlink DMRS signal. According to the official Huawei documentation, gNodeBs can use downlink DMRS signals or the DMRS of the uplink PUSCH of the UE to obtain downlink channel characteristics. The downlink DMRS signals contain information about the downlink channel characteristics, and the DMRS of the uplink PUSCH of the UE can be used to measure the uplink channel characteristics. The uplink SRS and PMI signals reported by the UE are used to determine the uplink channel characteristics. For more information, please see this link:

The X2 interface is a signaling interface used in LTE networks to interconnect two eNodeBs (LTE base stations) to support handover and other functions. In the inter-site DC solution, the X2 interface can also be used to implement the transmission interconnection between the LTE and NR sites.

In order to ensure smooth handover and service continuity between the LTE and NR sites, it is necessary to meet the requirement of low transmission delay, which is typically <20ms. This low delay requirement is important to ensure that the handover can be completed quickly and without interruption to the ongoing service.

The maximum number of PCIs (Physical Cell Identifiers) supported by a 5G network is 1008. This is specified in 3GPP 5G standard TS 38.211, which states that the maximum number of PCIs that a 5G network can support is 1008.

In 5G, each cell is assigned a unique identifier called the PCI (Physical Cell Identity). The PCI is used to identify the cell and its system information, and it is used for various purposes such as cell selection, handover, and interference management.

According to 3GPP specifications, the maximum number of PCIs that can be supported by a 5G network is 1008, which allows for a large number of cells to be deployed in a network. However, the actual number of PCIs used in a network will depend on the specific deployment scenario, the network architecture, and the capacity requirements of the network.