Free and Premium Cisco 500-220 Dumps Questions Answers

iOS devices that are using Apple's Device Enrollment Program (DEP) can be supervised and enrolled over-the-air anytime they are factory reset. DEP is the best way to permanently force your devices to be owned and managed by your organization, and it is important to assign your DEP settings properly before deployment. .

This can be determined by looking at the concentrator routing table and finding the entry for the destination IP 10.116.32.4. The next hop for this entry is the Auto VPN peer “Store 1532 – appliance”.

This question is related to the topic of Implementing Dynamic Routing Protocols in the Engineering Cisco Meraki Solutions (ECMS) official training documentation. You can find more information about this topic in the ECMS v2.2 Course Overview or the ECMS1 v2.1 Course Overview.

SM Sentry enrollment can be enabled on any MR network via the Splash page section of the Wireless > Configure > Access control page.

What happens if a network loses connectivity to the Meraki cloud?

Because of Meraki’s out of band architecture, most end users are not affected if Meraki wireless APs, switches, or security appliances cannot

communicate with Meraki’s cloud services (e.g., because of a temporary WAN failure):

• Users can access the local network (printers, file shares, etc.)

• If WAN connectivity is available, users can access the Internet

• Network policies (firewall rules, QoS, etc.) continue to be enforced

• Users can authenticate via 802.1X/RADIUS and can roam wirelessly between access points

• Users can initiate and renew DHCP leases

• Established VPN tunnels continue to operate

• Local configuration tools are available (e.g., device IP configuration

On the device, navigate to Settings > General > Device Management

Select Meraki Management, and select Remove to delete the management profile and any managed configuration profiles installed via SM

If you only need traffic statistics from your spoke site clients then you only need to enable insight on the spoke network as the hub site will not gather data for remote sites.

A license is only required for those networks where Meraki Insight functionality is desired. One license is required per network, regardless of whether that network has a single MX or HA pair. Licenses can be moved between networks, but historical data for the old network will be lost.

This is because the alert mentions 802.1X failure, which is a network access control method that is used with WPA2-enterprise and RADIUS servers1.

This question is related to the topic of Wireless Access Points Quick Start in the Cisco Meraki documentation. You can find more information about this topic in the Wireless Access Points Quick Start article or the Using the Cisco Meraki Device Local Status Page page.

This is the number of tunnels that each hub needs to support in a hub-and-spoke Auto VPN deployment with two NAT-mode hubs with dual uplink connections and 50 remote sites with a single uplink connection. This can be calculated by using the formula for the hub tunnel count in a hub-and-spoke topology1:

Hub Tunnel Count = (H x (H - 1) / 2 x L1) + (H x S x L1 x L2)

Where H is the number of hubs, S is the number of spokes, L1 is the number of uplinks for the hubs, and L2 is the number of uplinks for the spokes. In this case, H = 2, S = 50, L1 = 2, and L2 = 1. Therefore,

Hub Tunnel Count = (2 x (2 - 1) / 2 x 2) + (2 x 50 x 2 x 1) Hub Tunnel Count = (2 x 1 / 2 x 2) + (200 x 2) Hub Tunnel Count = (2 / 2 x 2) + (400) Hub Tunnel Count = (1 x 2) + (400) Hub Tunnel Count = 2 + 400 Hub Tunnel Count = 402

This question is related to the topic of Auto VPN Hub Deployment Recommendations in the Cisco Meraki documentation. You can find more information about this topic in the Auto VPN Hub Deployment Recommendations article or the Meraki Auto VPN General Best Practices page.

Verbs in the API follow the usual REST conventions:

GET returns the value of a resource or a list of resources, depending on whether an identifier is specified.

POST adds a new resource

PUT updates a resource

DELETE removes a resource

.

The number of devices in an organization can not exceed the license limits. If this occurs, the organization will enter a 30-day grace period, during which the organization must be brought back into compliance, otherwise it will be shut down until proper licensing is applied to the organization.

If a Meraki Access Point does not have a configuration from the Meraki Cloud Controller it will instead broadcast a default SSID of "Meraki-Scanning."

vs

-scanning

Cause: Similar to 'bad-gateway', an AP is unable to connect to its default gateway.

This is because the AP is broadcasting the default SSID “meraki-scanning” which is only broadcast when the AP has never connected to the Meraki Cloud Controller1.

This question is related to the topic of Wireless Access Points Quick Start in the Cisco Meraki documentation. You can find more information about this topic in the Wireless Access Points Quick Start article or the Using the Cisco Meraki Device Local Status Page page.