Complete H12-893_V1.0 Huawei Materials

In Huawei’s M-LAG (Multi-Chassis Link Aggregation), the heartbeat link (or peer-link) ensures communication between member devices. A fault in this link can impact M-LAG operation. Let’s evaluate each statement:

A. The fault that two master devices exist cannot be detected in the case of a peer-link fault:This is false. A peer-link fault can be detected, and mechanisms like dual-master detection (e.g., via Inter-Chassis Communication Link or ICC) can identify if both devices assume master roles, triggering corrective actions.FALSE.

B. An alarm is triggered:This is true. A peer-link fault generates an alarm to notify administrators, as it’s a critical failure in M-LAG operation, per Huawei’s fault management system.TRUE.

C. The fault protection mechanism is triggered:This is true. Huawei M-LAG includes protection mechanisms (e.g., failover to backup links or shutdown of conflicting interfaces) to mitigate peer-link faults and maintain service continuity.TRUE.

D. Services are affected:This is false. With proper configuration (e.g., redundant links or fast failover), services should not be affected by a peer-link fault, as M-LAG is designed for high availability. Impact depends on redundancy, but the design goal is uninterrupted service.FALSE.

Thus,A and Dare false statements because dual-master faults can be detected, and services are not necessarily affected with adequate redundancy.References:Huawei CloudEngine Series Switch Configuration Guide – M-LAG Fault Handling; HCIP-Data Center Network Training – M-LAG Reliability.

VXLAN (Virtual Extensible LAN) tunnels are used to encapsulate Layer 2 traffic over a Layer 3 network, a key component in Huawei’s CloudFabric data center solutions. Let’s evaluate each statement:

A. A VXLAN tunnel is identified by a pair of VTEPs:This is true. A VXLAN tunnel is identified by the pair of VXLAN Tunnel Endpoint (VTEP) IP addresses (local and remote), along with the VNI (VXLAN Network Identifier). This ensures unique tunnel identification.TRUE.

B. After a tunnel is established, if one end of the tunnel goes Down, the other end may not go Down:This is true. VXLAN tunnels are unidirectional, and the status of one end does not automatically affect the other unless the underlay network connectivity (e.g., Layer 3 reachability) is lost. The remote VTEP may remain operational if it can still encapsulate/decapsulate traffic.TRUE.

C. For a static tunnel, you need to manually configure the local and remote VNIs:This is true. In a static VXLAN tunnel, administrators must manually configure the VNI and VTEP IP addresses on both ends, as there is no dynamic control plane (e.g., BGP EVPN) to automate the process.TRUE.

D. Dynamic tunnels depend on EVPN Type 5 routes to transmit information:This is false. Dynamic VXLAN tunnels rely on BGP EVPN as the control plane, but Type 5 routes (IP Prefix routes) are specifically used for advertising host IP routes and external network routes, not for general tunnel establishment. Dynamic tunnel setup primarily uses Type 2 (MAC/IP Advertisement) and Type 3 (Multicast) routes to exchange VNI and VTEP information. Type 5 routes are relevant for Layer 3 routing, not the initial tunnel setup.FALSE.

Thus,Dis the false statement because dynamic tunnels depend on EVPN Type 2 and Type 3 routes, not Type 5, for initial establishment.References:Huawei CloudFabric Data Center Network Solution – VXLAN Configuration Guide; HCIP-Data Center Network Training – VXLAN Tunneling.

In a network overlay, VXLAN (Virtual Extensible LAN) tunnels extend Layer 2 networks over a Layer 3 underlay, commonly implemented in Huawei’s data center solutions. The endpoints of a VXLAN tunnel are VXLAN Tunnel Endpoints (VTEPs), which encapsulate and decapsulate traffic.

VTEP Roles:VTEPs can be physical switches (e.g., Huawei CloudEngine series), virtual switches (e.g., Open vSwitch on a hypervisor), or routers with VXLAN support. The endpoints are defined by their IP addresses, not their physical nature.

Deployment Flexibility:In modern data centers, VXLAN tunnels often connect physical switches to virtualized environments where VTEPs reside on hypervisors or servers hosting VMs. For example, a VM’s vNIC might connect to a virtual switch (VTEP) that tunnels to a physical switch VTEP. Thus, both endpoints are not always physical switches; one or both can be virtual.

The statement isFALSE (B)because both endpoints of a VXLAN tunnel are not necessarily physical switches; they can include virtual VTEPs in hypervisors or other devices.References:Huawei HCIP-Data Center Network Training – VXLAN Overlay; CloudFabric VXLAN Deployment Guide.

Virtualization technologies enable the creation of virtual machines (VMs) by abstracting hardware resources. Open-source technologies are freely available with accessible source code. Let’s evaluate each option:

A. Hyper-V:Hyper-V is a hypervisor developed by Microsoft, integrated into Windows Server and available as a standalone product. It is proprietary, not open-source, as its source code is not publicly available.Not Open-Source.

B. Xen:Xen is an open-source hypervisor maintained by the Xen Project under the Linux Foundation. It supports multiple guest operating systems and is widely used in cloud environments (e.g., Citrix XenServer builds on it). Its source code is freely available.Open-Source.

C. FusionSphere:FusionSphere is Huawei’s proprietary virtualization and cloud computing platform, based on OpenStack and other components. While it integrates open-source elements (e.g., KVM), FusionSphere itself is a commercial product, not fully open-source.Not Open-Source.

D. KVM (Kernel-based Virtual Machine):KVM is an open-source virtualization technology integrated into the Linux kernel. It turns Linux into a Type-1 hypervisor, and its source code is available under the GNU General Public License. It’s widely used in Huawei’s virtualization solutions.Open-Source.

Thus,B (Xen) and D (KVM)are open-source virtualization technologies.References:Huawei HCIP-Data Center Network Training – Virtualization Technologies; Official Xen Project and KVM Documentation.