Free and Premium LPI 702-100 Dumps Questions Answers

The correct configuration line for sending all messages from the auth facility to a remote syslog server is auth.* @logger.example.org. In syslog configuration, the auth.* specifies the facility and priority, where auth is the facility for security/authorization messages, and * represents all priorities. The @ symbol is used to indicate that the messages are to be sent to a remote server, followed by the hostname of the remote syslog server. References:

• FreeBSD Handbook - Logging
• Linux Professional Institute BSD Specialist Exam Objectives

The subnet mask 255.255.224.0 corresponds to the hexadecimal netmask 0xffffe000 shown in the output. This subnet mask indicates a subnet with 19 bits for the network portion and 13 bits for the host portion, allowing for a large number of hosts within the subnet.

References:

• BSD Specialist Exam 702 Objectives - Linux Professional Institute
• FreeBSD Handbook - Networking

The umask command in BSD is used to set default permissions for files or directories the user creates1. The umask value is permissions to deny, taken off whatever permissions would be given by default2. The default permission values for files are 666 (rw-rw-rw-), meaning read and write for user, group, and others3. The umask value of 022 means that the permissions to deny are 022 (—w–w-), meaning write for group and others. To calculate the default permissions for newly created files, we need to subtractthe umask value from the default permission value, using bitwise AND operation4. For example:

666 - 022 = 644 rw-rw-rw- - —w–w- = rw-r–r–

Therefore, the default permissions for newly created files with a umask of 022 are 644 (rw-r–r–), meaning read and write for user, and read for group and others.

References: 1: Umask command in Linux with examples - GeeksforGeeks 2: Different permission between directory and file with ‘umask’ - Unix & Linux Stack Exchange 3: Default File Permissions (umask) - docs.oracle.com 4: What is Umask and How to Use It {Update Default Linux File Permissions} - phoenixNAP KB

The /etc/printcap file on a BSD system defines the printers that are available by the Ipr printing system. The Ipr printing system is a BSD-compatible printing system that uses the lpd daemon to manage print jobs and spooling. The /etc/printcap file contains a series of entries, one for each printer, that specify the printer name, device, options, and filters. The format and syntax of the /etc/printcap file are described in the printcap(5) manual page. References:

• About Printing on FreeBSD | The FreeBSD Forums
• The BSD Printing Protocol (System Administration Guide, Volume 2) - Oracle
• Chapter 11. Printing | FreeBSD Documentation Portal

The ports collection on FreeBSD is a package management system that allows users to install third-party software from source or binary packages. The ports collection is stored in the /usr/ports/ directory, which contains subdirectories for different categories of software, such as archivers, databases, editors, etc. Each subdirectory contains one or more ports, which are directories that contain the files needed to build and install the software. The /usr/ports/ directory can be updated with the portsnap command34

Binary packages are pre-compiled versions of the ports that can be installed with the pkg command. Binary packages are downloaded from the FreeBSD package repository,which is hosted at pkg.freebsd.org. The packages are installed in the /usr/local/ directory by default, and the information about the installed packages is stored in the /usr/local/pkg/ directory. The /usr/local/pkg/ directory contains files with the .db extension, which are SQLite databases that store the metadata of the packages. The pkg command can query and manipulate these databases56 References: 3: 4: 5: 6: &sektion=8

The file /etc/rc.conf contains values for Management Information Bases (MIBs) which are set during system startup. This file is used to configure system-wide settings, including the enabling and disabling of services, network settings, and other startup configurations2.

References:

• FreeBSD Handbook - The FreeBSD Booting Process

The cron job syntax consists of five fields that specify the time and date of execution, followed by the command or script to run. The fields are: minute, hour, day of month, month, and day of week. Each field can have a specific value, a range, a list, a wildcard (), or a step value. The wildcard () means any possible value for that field. The option B sets the minute field to 0 and the hour field to *, which means the script will run at the 0th minute of every hour, regardless of the day, month, or weekday. This is equivalent to once per hour. The other options are either invalid syntax or do not match the desired frequency. For example, option A sets all fields to *, which means the script will run every minute of every hour of every day, month, and weekday. Option C sets the minute field to * and the hour field to 0, which means the script will run every minute of the 0th hour, or once per day at midnight. Option D has a typo (o instead of *) and option E sets the day of month field to o, which is not a valid value. References:

• crontab - FreeBSD crontab(5) Manual Page1
• Crontab Explained in Linux [With Examples] - Linux Handbook2

The -e option of the crontab command opens the current user’s crontab in an editor. The editor used is determined by the environment variables VISUAL or EDITOR. If neither of these variables is set, the default editor is vi. The user can edit the crontab file to add, modify, or delete cron jobs, which are scheduled commands or scripts that run at a specified time or interval. The crontab file has the following format:

minute hour day-of-month month day-of-week command

Each field can be a number, a range, a list, or an asterisk (*), which means all possible values. The command can be any valid shell command or script. For example, the following crontab entry runs the backup.sh script every day at 2:30 AM:

30 2 * * * /home/user/backup.sh

To save and install the crontab file, the user needs to exit the editor. The crontab command will check the syntax of the file and report any errors. If the file is valid, it will be installed and the cron daemon will execute the cron jobs according to the schedule. References:

• crontab(1) - Linux manual page
• FreeBSD Handbook: 11.6. Scheduling Tasks

The command locate.updatedb updates the database used by locate to find files. The locate command searches for files by name in a pre-built database of files and directories. The database is usually updated periodically by a cron job, but the locate.updatedb command can be used to manually update it. The command may require root privileges to run, depending on the system configuration. References:

• BSD Specialist Exam 702 Objectives, Topic 715: Basic Unix Skills, 715.4 Searching and Extracting Data from Files
• FreeBSD Handbook, Chapter 7: Finding and Installing Software, 7.2.3 Using locate(1) to Find Files Quickly

According to the BSD disklabel documentation1, the device name for a BSD disk slice consists of three parts: the disk name, the partition letter, and the slice number. The disk name is determined by the driver and the order of detection, and it usually follows the pattern of sdX, where X is a letter from a to z. The partition letter is a lowercase letter from a to p, excluding c, which is reserved for the whole disk. The slice number is a decimal number from 0 to 15, indicating the MBR partition that contains the BSD disklabel. Therefore, the device name for the first BSD disk slice in the disk label on the first partition on the second SATA disk on OpenBSD is /dev/sdlp2d, where sdl is the disk name, p is the partition letter, and 2 is the slice number.

References1: BSD disklabel - Wikipedia

The name of the NetBSD installation program is sysinst. It is the standard installer used by NetBSD for setting up the system on a new machine. The sysinst program guides users through the installation process, including disk partitioning, package selection, and system configuration45.

References:

• NetBSD Guide - Example installation
• NetBSD Guide - Installing NetBSD: Preliminary considerations and preparations

The inetd.conf file is the configuration file that needs to be edited before the TFTP service will start on a BSD system. The inetd daemon handles the TFTP service and other network services, and its configuration file contains settings that determine howthese services are managed. To enable the TFTP service, the corresponding entry in inetd.conf must be uncommented and properly configured. References:

• FreeBSD Handbook - inetd
• Linux Professional Institute BSD Specialist Exam Objectives

The question mark (?) is a special character in regular expressions that modifies the preceding expression to match zero or one times. For example, the regular expression colou?r matches both color and colour, but not colouur or colr. The question mark is also used to make an expression non-greedy, meaning that it will match the shortest possible string instead of the longest. For example, the regular expression <.?> matches the first pair of angle brackets in a string, while <.> matches the entire string enclosed by the outermost pair of angle brackets. References:

• Regular expression - Wikipedia, section “Basic concepts”
• How to write Regular Expressions? - GeeksforGeeks, section “Special Characters”

The setenv command is used to set an environment variable in the csh or tcsh shell. The syntax is setenv VAR VALUE, where VAR is the name of the variable and VALUE is the value to assign to it. The TZ variable is used to specify the timezone for the shell and its subprocesses. To set the timezone to GMT (Greenwich Mean Time), the command is setenv TZ GMT. This will affect the output of commands like date and ls that display time information. The other options are either invalid syntax or belong to other shells, such as bash or sh. References:

• setenv - Linux setenv command help and examples1
• TZ - FreeBSD Environment Variables2

The date command in BSD systems provides the following features:

• It outputs the time in a specific format. The date command can display the current date and time in various formats, depending on the options and arguments given. For example, the command date +%Y-%m-%d will output the date in the format of year-month-day, such as 2023-04-30. The command date +%T will output the time in the format of hour:minute:second, such as 22:51:42. The command date +%A will output the full name of the weekday, such as Thursday. The date command supports many formatting characters that can be used to customize the output. For a full list of formatting characters, see the date(1) manual page1.
• It sets the clock to a specific time. The date command can also be used to set the system date and time, if the user has the appropriate privileges. For example, the command date 0430225123 will set the date and time to April 30, 2023, 22:51:42. The command date -u 0430225123 will set the date and time to the same value, but in UTC (Coordinated Universal Time) instead of the local time zone. The command date -n will set the date and time to the current network time, using the ntpd(8) daemon1.

The date command does not provide the following features:

• It does not display a calendar. The date command only displays the date and time, not a calendar. To display a calendar, the cal(1) or ncal(1) commands can be used instead. For example, the command cal 4 2023 will display the calendar for April 2023. The command ncal -w 2023 will display the calendar for the whole year 2023, with week numbers23.
• It does not send NTP queries. The date command does not send any network requests or queries to NTP (Network Time Protocol) servers. To synchronize the system clock with NTP servers, the ntpd(8) daemon or the ntpdate(8) utility can be used instead. For example, the command ntpd -q will query one or more NTP servers and adjust the system clock accordingly. The command ntpdate pool.ntp.org will set the date and time to the value returned by the NTP server pool.ntp.org45.
• It does not change the system’s timezone. The date command does not change the system’s timezone setting, only the date and time values. To change the system’s timezone, the tzsetup(8) utility or the ln(1) command can be used instead. For example, the command tzsetup will run an interactive program that allows the user to select a timezone from a list of regions and cities. Thecommand ln -sf /usr/share/zoneinfo/Europe/Paris /etc/localtime will create a symbolic link from the file /etc/localtime to the file /usr/share/zoneinfo/Europe/Paris, which contains the timezone information for Paris, France . References:
• date(1) - FreeBSD
• cal(1) - FreeBSD
• ncal(1) - FreeBSD
• ntpd(8) - FreeBSD
• ntpdate(8) - FreeBSD
• [tzsetup(8) - FreeBSD]
• [ln(1) - FreeBSD]

The command route add default 192.168.1.1 is used to set the default gateway on a BSD system. This command adds a default route to the routing table, directing traffic to the specified gateway IP address when no other route matches.

References:

• FreeBSD Handbook - Routing
• OpenBSD Change, Add or Display Default Gateway

The pgrep command is used to find processes by various criteria, such as user name, group name, process ID, command name, etc. The -u option specifies the user name or user ID to match. Therefore, the command pgrep -u bob will show all processes owned by the user bob. The output will be a list of process IDs, one per line. To show more information about the processes, such as command name, arguments, state, etc., the -l, -a, and -f options can be used. For example, the command pgrep -l -u bob will show the process ID and the command name for each process owned by bob. References:

• pgrep - FreeBSD, the manual page for the pgrep command on FreeBSD.
• How to use pgrep and pkill commands in Linux - Linuxize, a tutorial on how to use the pgrep and pkill commands in Linux.

The file command is used to determine the type of data contained in a computer file. It performs a series of tests on the file and prints a description of the file type based on the first successful test. The file command can take one or more file names as its arguments. For example, file mybackup will display the file type of mybackup. The other options are not valid commands for finding the file type. References:

• file command in Linux with examples
• file (command) - Wikipedia
• Linux File Command