Free and Premium Huawei H35-580_V2.0 Dumps Questions Answers

According to the NR-ARFCN (NR absolute radio frequency channel number), the NR-ARFCN value consists of two components: the band indicator and the channel number. The band indicator represents the frequency band on which the carrier frequency lies, while the channel number represents the specific carrier frequency within that band. The NR-ARFCN value is calculated by the following formula:

NR-ARFCN = FREF-Offs + NREF-Offs + ΔFGlobal * (Fcarrier - FREF-Offs) / AFGIobal

where FREF-Offs is the reference frequency offset, NREF-Offs is the reference NR-ARFCN offset, ΔFGlobal is the global frequency raster, Fcarrier is the carrier frequency, and AFGIobal is the absolute frequency granularity.

Given that AFGIobal is 15 kHz, FREF-Offs is 3000 MHz, and NREF-Offs is 600000, we can plug in these values and Fcarrier = 3300 MHz into the formula and get:

NR-ARFCN = 3000 + 600000 + 5 * (3300 - 3000) / 0.015 NR-ARFCN = 633000

Therefore, the correct answer is A.

According to the Hardware Description: Bbu5900 V100r013c10, these statements are correct about the space principles for 5G BBU installation:

• If the installation space is insufficient, the BBU can be installed on a wall. Ensure that the wall meets the load bearing requirements: The BBU can be installed on a wall using wall-mounted brackets. The wall must be able to bear at least four times the weight of the BBU and must be flat and vertical. The installation height of the BBU must not exceed 2 m.
• If the space is greater than 600 mm, a cabinet can be added to install the BBU: The BBU can be installed in a cabinet that meets the requirements of Huawei base stations. The cabinet must have a width of 19 inches and a depth of at least 600 mm. The cabinet must also provide sufficient ventilation, grounding, and lightning protection for the BBU.
• If the remaining space of an existing cabinet is greater than 4 U, the BBU can be installed directly: The BBU can be installed in an existing cabinet that has enough space for it. The BBU has a height of 2 U, so it requires at least 4 U of space in a cabinet. The existing cabinet must also meet the requirements of Huawei base stations.

The other statement is incorrect about the space principles for 5G BBU installation:

• If the installation space is insufficient, install 5G boards directly into the existing 4G B8U: This statement is not supported by Huawei base stations. The 5G boards cannot be installed directly into the existing 4G B8U because they have different slot distributions and board types. The 5G boards can only be installed in a BBU5900 subrack that supports both LTE and NR modes.

The link budget parameters that may differ depending on use in either densely populated urban areas or rural areas are area coverage rate, shadow fading margin, and penetration loss. The area coverage rate is the percentage of area within a cell that can receive a signal above a certain threshold. In densely populated urban areas, the area coverage rate may be lower than in rural areas due to more interference and obstacles 13. The shadow fading margin is an additional margin added to the link budget to account for the variation of signal strength due to obstacles in the propagation path. In densely populated urban areas, there may be more buildings and structures that cause shadow fading than in rural areas, so a larger shadow fading margin may be needed 14. The penetration loss is the loss of signal strength when it passes through walls or windows into buildings. In densely populated urban areas, there may be more indoor users than in rural areas, so a larger penetration loss may be considered 15. The antenna gain is not a parameter that depends on use in either densely populated urban areas or rural areas. It is a parameter that depends on the antenna design and configuration, which are usually fixed for a given system 16.

According to the Career Certification - Huawei Enterprise, single site verification is used to test and verify the equipment functions and coverage capability after gNodeB hardware is installed and commissioned, which corresponds to option C.

According to the Blind handover or blind redirection method and system, A3 is the event that is used by the gNodeB to trigger a blind redirection procedure. A3 is defined as “neighbour becomes offset better than serving” in 3GPP TS 38.331. When the gNodeB detects that the UE’s signal quality on a neighbouring cell is better than that on the serving cell by a certain offset, it can initiate a blind redirection procedure to switch the UE to the neighbouring cell without requiring measurement reports from the UE.

According to the Huawei Releases 5G Series Products, Huawei’s AAU5313 and AAU5613 are both RF modules that support 64T64R. The AAU5313 is an ultra-wideband Massive MIMO product that supports both 64T64R and 400 MHz bandwidth on the C-band. The AAU5613 is a BladeAAU Pro product that supports 64T A+P integration on sub-3 GHz bands. The AAU5612 is a BladeAAU product that supports only 32T A+P integration on sub-3 GHz bands. The RRU3939 is not an AAU product but an RRU (Remote Radio Unit) product that supports only 8T8R on sub-3 GHz bands.

According to the HCIA-5G V2.0 Exam Outline, cell unavailability due to system faults (specified using N.Cell.Unavail.Dur.System) is caused by factors such as CPRI link faults, board faults, and faults on an RF module’s TX or RX channels, which correspond to options A, C, and D. Blocking cells by using MML commands is not a system fault, but a manual operation, which corresponds to option B.

According to the HCIA-5G V2.0 Exam Outline, handover execution failures can use the counters to collect failure reasons in SA networking, which corresponds to option A. The counters include N.HO.Exec.Fail.RadioResFail, N.HO.Exec.Fail.TAExceed, N.HO.Exec.Fail.NoRespFromUE, and N.HO.Exec.Fail.Other.

According to the 5G NR Physical Layer Specifications, demodulation reference signals (DMRSs) are required for the following channels/signals in the downlink and uplink:

• Downlink Physical Broadcast Channel (DPBCH)
• Downlink Physical Downlink Control Channel (DPDCCH)
• Downlink Physical Shared Channel (DPOSCH)
• Uplink Physical Random Access Channel (PRACH)
• Uplink Physical Uplink Control Channel (PUCCH)
• Uplink Physical Uplink Shared Channel (PUSCH)

According to the Huawei 5G Base Station Product Description, the following boards support CPU usage query:

• UPEU (Universal Power and Environment Interface Unit): It provides power supply and environment monitoring functions for other boards in a subrack. It supports CPU usage query through commands or web pages.
• UMPT (Universal Main Processing and Transmission Unit): It provides main processing and transmission functions for a subrack. It supports CPU usage query through commands or web pages.
• UBBP (Universal Baseband Processing Unit): It provides baseband processing functions for a subrack. It supports CPU usage query through commands or web pages.

The FAN (Fan Unit) does not support CPU usage query because it does not have a CPU.

According to the HCIA-5G V2.0 Exam Outline, in the NSA DC architecture, when a UE moves to a neighboring gNodeB, the SgNB change procedure is triggered, which corresponds to option D.

According to the eCPRI Specification V2, eCPRI links have the following characteristics:

• They require clock synchronization: eCPRI links use Ethernet as the transport layer, which does not provide inherent synchronization. Therefore, eCPRI links require external clock synchronization methods, such as IEEE 1588v2 Precision Time Protocol (PTP) or Synchronous Ethernet (SyncE).
• They are based on the IP mechanism: eCPRI links use IP as the network layer, which provides routing and addressing functions for eCPRI messages. eCPRI links can use either IPv4 or IPv6 protocols.
• They require AAU support: eCPRI links connect between Radio Equipment Control (REC) and Radio Equipment (RE) in a base station. AAU (Active Antenna Unit) is a type of RE that integrates RF and antenna functions in one unit. Therefore, eCPRI links require AAU support to enable flexible functional split options and reduce fronthaul bandwidth requirements.

eCPRI links are not based on the TDM mechanism because they do not use fixed time slots to transmit data. Instead, they use variable-length packets to transmit data according to different service requirements.

According to the 5G NR Downlink CSI Reporting, CSI-RS is the channel/signal that is used by the UE to measure and obtain the CQI. CSI-RS stands for Channel State Information Reference Signal, which is a downlink reference signal transmitted by the gNodeB to enable the UE to estimate the channel quality and feedback the CQI to the gNodeB. The CQI is an indicator of how good or bad the channel quality is, and it can be used by the gNodeB to adjust the modulation and coding scheme for data transmission.

According to the 5G-GUTI - 5G Globally Unique Temporary Identity, the NAS layer uses 5G-GUTI to replace IMSI as the temporary ID of a UE for security reasons. The 5G-GUTI is allocated by the AMF (Core Access and Mobility Management Function) at the time of network registration, and it is composed of the GUAMI (Globally Unique AMF ID) and the 5G-TMSI (5G Temporary Mobile Subscriber Identity).

According to the 5G mmWave Frequency Bands, the maximum bandwidth in mmWave bands as defined in 3GPP Release 16 is 400MHz, which can be achieved without any carrier aggregation method.

 According to the Huawei Career Certification Learning, 5G can meet service requirements in scenarios with a mobility speed of up to 500 km/h, which is much higher than the 4G limit of 350 km/h.

According to the HCIA-5G V2.0 Exam Outline, the statements in options A, B, and C are correct descriptions of throughput-related indicators, which correspond to options A, B, and C. The statement in option D is incorrect because adding the last small packet of each data transmission burst and its transmission duration will reduce the accuracy of throughput measurement.