CertsTopics Logo

Black Friday Special 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: save70

Free and Premium HP HPE2-T37 Dumps Questions Answers

Page: 1 / 9
Total 115 questions
Get HPE2-T37 Full Access Download HPE2-T37 PDF

Using HPE OneView Questions and Answers

Question 1

A customer wants to estimate the cost of the licenses required to manage HP€ Synergy and some external components When component includes an HPE OneView license for management?

Options:

A.

Compute Module

B.

Storage Array

C.

Master Module

D.

Logical Enclosure

Buy Now
Question 2

Which statement about a server profile for an Apollo system is true?

Options:

A.

Fibre Channel connections can be defined

B.

UEFI optimized is the only available boot mode

C.

Virtual WWNs and MAC addresses can be defined

D.

Enclosure Group Is automatically selected

Question 3

Which statement about the presented storage pools is true?

Options:

A.

Storage pools in discovered state can be removed from HPE OneView.

B.

HPE OneView can be used to configure replication only between managed storage pools

C.

All storage pools from the system named ThreePAR-1 can be used for volume provisioning

D.

All storage pools in managed state have a valid HPE OneView license applied

Question 4

Click the option that will allow you to disable virtual MAC addresses or generate a new pool of virtual Worldwide Names.

Options:

Question 5

Click the option that will allow you to update the firmware of master and satellite modules.

Options:

Question 6

what is required to add a remote frame to the primary management ring?

Options:

A.

UUD of the remote HPE Composer

B.

Serial number of one of the remote frames

C.

Remote frame Link Module IPv6 address

D.

Request code from the primary HPE Composer

Question 7

You want a server profile to be automatically applied when an HPE Synergy Compute Module is replaced.

Click the appropriate configuration option.

Options:

Question 8

You have created volumes using array management tools and imported the volumes to HPE OneView.

Which statement about these volumes is true?

Options:

A.

Imported volumes are treated as private volumes and can be only used as boot volumes

B.

Volumes imported to HPE OneView is managed just like a volume created using HPE OneView

C.

Volumes imported to HPE OneView cannot be removed using the HPE OneView interface

D.

A snapshot for imported volumes can be created only by using array management tools

Question 9

What event occurs on iLO when an HPE ProLiant server is added to HPE OneView?

Options:

A.

IPMI credentials are configured for the iLO

B.

REST API plugin is enabled for iLO

C.

Active Directory configuration is performed on iLO

D.

SSO certificate is added to the iLO

Question 10

Which parameters can be defined in a server profile template for HPE Synergy Compute Modules? (Select two.)

Options:

A.

partition layout for servers running Linux.

B.

IL0 IPv4 or IPv6 address.

C.

local storage and BIOS settings.

D.

NIC teaming setup at OS level.

E.

network and storage connectivity.

Question 11

You have to move a server profile from a server to the other server. What must be done prior server profile migration?

Options:

A.

Source system has to be placed in a maintenance mode.

B.

Target system must be powered off.

C.

Source server has to be powered on.

D.

Target server has to be placed in a maintenance mode.

Question 12

Which statement about RoCE network restrictions is true?

Options:

A.

RoCE networks require Virtual Connect SE 32Gb FC Modules.

B.

RoCE networks cannot be configured when Virtual Connect modules are used.

C.

RoCE networks are supported only when PVLANs are enabled.

D.

RoCE networks are not supported with HPE BladeSystem

Question 13

Refer to the exhibit.

Which statement about the logical interconnect shown is true?

Options:

A.

For FC uplink sets, an additional uplink from second module should be added for redundancy.

B.

The maximum supported number of the internal networks for logical interconnect is configured.

C.

Additional uplink ports can be added to ETH-Uplink to increase available bandwidth.

D.

FC uplinks are not supported and will be converted to FCoE or RoCE uplinks.

Question 14

Which statement about a Logical Enclosure for HPE BladeSystem is Hue?

Options:

A.

A logical enclosure can have between 1 to 5 HPE BladeSystem c7000 enclosures.

B.

A logical enclosure must be created only for monitored HPE BladeSystem C700O enclosures.

C.

A logical enclosure is created automatically, and it is always based on a single enclosure.

D.

A logical enclosure can contain a mix of HPE BladeSystem c7000 and C3000 enclosures.

Question 15

What is the maximum number of HPE Synergy frames that can formulate a single logical enclosure when 25Gb connectivity is used for all HPE Synergy compute nodes?

Options:

A.

21

B.

1

C.

3

D.

5

Question 16

Which statement about M-LAG setup is true?

Options:

A.

When combined with IRF, M-LAG will allow you to aggregate ports coming from clustered HPE Synergy Virtual Connect modules.

B.

M-LAG for HPE Synergy can be either single-homed or multi-homed, while for HPE BladeSystem only single-homed.

C.

sFLOW cannot be enabled if M-LAG is configured between HPE Synergy Virtual Connect modules in the same frame.

D.

M-LAG has to be defined manually for HPE BladeSystem, but it is automatically configured for HPE Synergy.

Question 17

Which statement about server hardware types is true?

Options:

A.

Once selected in the server profile, the server hardware type cannot be changed, and a server profile can be moved only between the same type of servers

B.

Server hardware type can be defined only for HPE Synergy and HPE BladeSystem, but it cannot be defined for HPE ProLiant or Apollo systems

C.

Administrator has to manually define the server hardware type for any unique server architecture and mezzanine card combination

D.

The server hardware type is automatically created when a server with unique architecture and mezzanine card configuration is added to HPE OneView

Question 18

How is HPE Storage Integration Pack for VMware vCenter deployed?

Options:

A.

It is deployed as an agent on any supported and managed array.

B.

It |i deployed as a virtual appliance to the supported hypervisor.

C.

It is the part of the standard HPE OneView appliance, but it must be activated.

D.

It is deployed as an application on Windows system running in the virtual machine.

Question 19

What is required to add remote frame link topology to HPE OneView?

Options:

A.

The HPE OneView certificate from the primary site must be added to HPE OneView in the remote site.

B.

The IP address assigned to HPE Composer installed in a remote site must be registered in a primary site.

C.

Multi-site licenses must be added to HPE OneView and activate for all available HPE Synergy frames.

D.

Management ports of the remote frame link topology must be connected to the management LAN.

Question 20

Your customer has tried to delete a volume using HPE OneView interface, but the operation has failed. Which of the following statements would cause the operation to fail?

Options:

A.

This volume is presented to the server.

B.

This volume is marked as permanent.

C.

This volume has at least one snapshot created.

D.

This volume is rebuilding after the drive failure.

Question 21

Which iL0 parameter can be configured using HPE OneView server profile?

Options:

A.

iLO Federation Group.

B.

iLO firmware repository.

C.

Active Directory integration.

D.

Access to the remote console.

Question 22

You want to put two FlexNlCs into a single Link Aggregation Group within a server profile. What Is a prerequisite for this setup?

Options:

A.

The sFlow option must be enabled and configured.

B.

Both FlexNlCs must be connected to the same network.

C.

The Compute Module profile must have exactly two connections defined.

D.

An upgrade license must be purchased and deployed.

Question 23

What can De defined in a server profile for HPE Superdome Flex?

Options:

A.

nPartition configuration.

B.

BMC settings.

C.

Complex firmware baseline.

D.

Ethernet connections.

Question 24

Your customer wants to add a rack system to HPE OneView. How can this task be completed?

Options:

A.

Rack systems can be added if the appropriate license is installed.

B.

Rack systems are automatically discovered if they contain a managed server.

C.

Rack systems can only be defined for HPE Synergy components.

D.

Rack systems can be denned manually using the HPE OneView interface.

Question 25

Which statement regarding HPE OneView backup restore is true?

Options:

A.

During backup restore, users with Administrator privileges can still login to HPE OneView

B.

An HPE OneView backup can be used to restore individual components like server profile

C.

Users with Backup Administrator privileges can restore an HPE OneView backup

D.

Only users with Infrastructure Administrator privileges can restore an HPE OneView backup

Question 26

Which statement about the volume template is true?

Options:

A.

Users will be able to change sharing type and volume capacity

B.

A volume created using this template will not support deduplication

C.

A volume created using this template mil not support snapshots

D.

Users will be able to select storage pool during volume creation

Question 27

Which statement about managing an HPE BiaoeSystem sever is true?

Options:

A.

A muiti-enclosure Vrtuai Connect domain can be imported to HPE OneView without disrupting servers

B.

An HPE server blade can be removed trom HPE OneView by deleting the server from the Server Hardware section

C.

An HPE server blade cannot be deleted from HPE OneView It must be physically removed from the enclosure

D.

Both c3000 and C7000 HPE BladeSystems enclosures can be imported to HPE Oneview for monitoring

Question 28

Which types of support dump can be created using HPE OneView? (Select two.)

Options:

A.

Enclosure group support dump

B.

Appliance support dump

C.

Firmware deployment support dump

D.

Logical enclosure support dump

E.

Maintenance console support dump

Question 29

Your customer runs VMware ESXi on an HPE Synergy platform. The ESXi systems must have access to 50 VLANs initially. However, this is a dynamic environment, and more VLANs will be added in the future.

They want to add more networks for virtual machines, but they do not want to modify the HPE Virtual Connect configuration.

Which type of the network should the customer define?

Options:

A.

Untagged

B.

Internal

C.

Tunnel

D.

Tagged

Question 30

Which of the following is a characteristic of the RoCE network type?

Options:

A.

It has Quality of Service enabled by default.

B.

It is always configured as a private network.

C.

It must be a tagged network.

D.

It has smart link enabled at all times.

Question 31

Refer to the exhibit.

Which statement about the storage pools shown is true?

Options:

A.

Volumes created on the first storage pool cannot use data reduction technologies

B.

Both storage pools are in a managed state and can be used for volume provisioning

C.

HPE OneView can be used to configure volume replication between these pools

D.

Both storage pools have a license applied that enables management of these pools

Question 32

Your customer wants to create a volume on a specific CPG within an HPE Primera array using the HPE OneView interface, but that CPG is not available for a volume provisioning.

What should you verify to solve the problem?

Options:

A.

The WSAPI and VASA provider are enabled on the array.

B.

The CPG was imported as a managed storage pool.

C.

The array has a proper license in HPE oneView.

D.

The array is enabled for HPE OneView management.

Question 33

You are deploying HPE OneView to manage a customer's HPE ProLiant servers

Is this statement about appliance availability true?

Options:

A.

HA features for HPE OneView are enabled only if the appliance is deployed on an HPE SimpliVity cluster

B.

HPE OneView has a built-in HA feature that can be activated with an additional license

C.

HPE OneView availability relies on HA features provoed by the hypervisor

D.

During hpe oneView deployment customer may select configure proprietary HA mode.

Question 34

Refer to the exhibit.

Your customer created multiple networks in HPE OneView, but only Eth-1 is available to be used within a server profile. What is a likely cause of this situation?

Options:

A.

The other networks are not configured with the required Smart Link parameter.

B.

The other networks are not added to the Logical Interconnect Group configuration.

C.

The other networks have Private Network' selected, which hides them from Compute Modules.

D.

The other networks are configured with a purpose other than General or Management.

Exam Detail
Vendor: HP
Certification: HPE Product Certified - OneView [2022]
Exam Code: HPE2-T37
Exam Name: Using HPE OneView
Last Update: Nov 23, 2024
HPE2-T37 Question Answers
Page: 1 / 9
Total 115 questions
Get HPE2-T37 Full Access Download HPE2-T37 PDF