New Year Special 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: save70

Free and Premium Netapp NS0-093 Dumps Questions Answers

Page: 1 / 5
Total 61 questions

NetApp Accredited Hardware Support Engineer Questions and Answers

Question 1

When you add a new disk to an ONTAP 9.1 system, you see an error that the disk “has raid label with version (16), which is not within the currently supported range (14-15).” What is one possible cause of this error?

Options:

A.

The disk is a non-zeroed spare.

B.

The disk firmware is too new for ONTAP software.

C.

The disk needs to be assigned to the new system.

D.

The disk was in a system with a newer version of ONTAP software

Buy Now
Question 2

In a SAS stack of shelves, what is the topology of the connection between expander and disk?

Options:

A.

arbritrated loop

B.

point-to-point

C.

loop

D.

ring

Question 3

What happens when the command diskcopy is run from nodeshell?

Options:

A.

It pre-fails a drive in an aggregate and copies it to a spare.

B.

It performs a low-level copy of the disk to another disk.

C.

It copies the disk content to a specified volume.

D.

It triggers a RAID reconstruction of that disk.

Question 4

What are two valid options for uploading a core file from a node that is running ONTAP 9.12.1 software to NetApp for analysis? (Choose two.)

Options:

A.

system node autosupport invoke -diagnostic

B.

Download via CIFS and upload to upload.netapp.com.

C.

Download via Service Processor Infrastructure (SPI) and upload to upload.netapp.com.

D.

system node autosupport invoke-core-upload

Question 5

While performing a health check on a cluster, you notice the following entries in the cluster event log:

Referring to the exhibit, which of the following actions do you take?

Options:

A.

Sanitize the disk.

B.

Reseat the disk.

C.

Review the current firmware and known issues.

D.

Use diskcopy to copy the disk to a working spare.

Question 6

Which RAID type provides protection against three disk failures?

Options:

A.

RAID DP

B.

RAID-TEC

C.

RAID 5

D.

RAID 4

Question 7

Which two statements are correct when describing L1 and L2 Watch Dog Resets (WDR)? (Choose two.)

Options:

A.

L2 WDR requests creation of a core dump before reset.

B.

L1 WDR is initiated after 0.5 seconds from the event.

C.

L1 WDR performs a soft reset.

D.

L2 WDR is initiated after 2 seconds from the event.

Question 8

Which two commands confirm whether an aggregate is WAFL inconsistent? (Choose two.)

Options:

A.

wafiron show

B.

node run –node sysconfig –r

C.

storage aggregate show

D.

node run –node sysconfig –a

Question 9

On an AFF A700 system, a SAS stack is connected to SAS ports 2a and 2b. The system has an additional 4-port SAS card in slot 9.

How should the cabling the corrected for best practices?

Options:

A.

Use port 2a and 9a.

B.

Use port 2a and 9b.

C.

Use port 2a and 2c.

D.

Use port 2b and 9d.

Question 10

During which two operations is the NVRAM replayed by the high-availability (HA) partner? (Choose two.)

Options:

A.

after triggering a sync core

B.

when a node is halted

C.

during a negotiated takeover

D.

when the node loses power

Question 11

How do you set environment variables to factory settings?

Options:

A.

set-defaults

B.

unsetenv all

C.

setenv factory

D.

wipeconfig

Question 12

You have upgraded your cluster from ONTAP 9.5 software to ONTAP 9.7 software. After the upgrade, you notice that the upgrade causes issues. You decide to revert to ONTAP 9.5 software.

Which revert step is allowed?

Options:

A.

Revert to ONTAP 9.5 software with the netboot procedure.

B.

Revert from ONTAP 9.7 software to ONTAP 9.5 software by using the boot backup procedure.

C.

Revert directly from ONTAP 9.7 software to ONTAP 9.5 software.

D.

Revert from ONTAP 9.7 software to ONTAP 8.6 software and then to ONTAP 9.5 software.

Question 13

Which two tools can be used to recover an inconsistent aggregate? (Choose two.)

Options:

A.

file check

B.

wafl_check

C.

wafl snapiron

D.

wafliron

Question 14

In the latest MANAGEMENT LOG AutoSupport message, you try to inspect the ENVIRONMENT section but find it empty.

In which section of AutoSupport can you find the reason?

Options:

A.

AUTOSUPPORT-BUDGET.XML

B.

HEADERS

C.

AUTOSUPPORT-HISTORY.XML

D.

MANIFEST.XML

Question 15

Which two factors can increase the chances of experiencing a NetApp WAFL inconsistency on an aggregate? (Choose two.)

Options:

A.

ignoring NetApp Active IQ health risks

B.

constantly running at high load

C.

using outdated disk firmware

D.

upgrading frequently

Question 16

What is the default amount of time that a volume is available for recovery from the volume recovery queue following a volume deletion?

Options:

A.

12 hours

B.

48 hours

C.

72 hours

D.

24 hours

Question 17

A SAS connection is reporting a single PHY down.

What are the two most likely causes? (Choose two.)

Options:

A.

improperly seated cable

B.

outdated I/O module (IOM1 firmware

C.

defective cable

D.

an offline shelf in the stack

Question 18

Which two statements regarding drive 1.2.3.L1 are true? (Choose two.)

Options:

A.

The drive is in shelf 2.

B.

The drive is in bay 3.

C.

The drive is in bay 2.

D.

The drive is in shelf 1.

Page: 1 / 5
Total 61 questions